Мануал yamaha yz250f

CHAS FRONT FORK 4. SPEC WARTUNGSDATEN Bezeichnung Standard Grenzwert Schmiersystem: COMPOSANTS ELECTRIQUES ET SCHEMA DE CABLAGE ELEKTRISCHE BAUTEILE UND SCHALTPLAN — ELEC COMPONENTI ELETTRICI E SCHEMA ELETTRICO PARTIE ELEKTRISCHE IMPIANTO ELECTRIQUE ANLAGE ELETTRICO ELEKTRISCHE BAU- COMPOSANTS COMPONENTI TEILE UND SCHALTPLAN ELECTRIQUES ET ELETTRICI E SCHEMA SCHEMA DE CABLAGE ELEKTRISCHE BAUTEILE ELETTRICO 1 Motorstoppschalter COMPOSANTS ELECTRIQUES ENGINE TUNING correctly and opens and closes CONSTRUCTION OF smoothly. Page INSP VALVE CLEARANCE INSPECTION AND ADJUSTMENT NOTE:

Disconnect the ignition coil from spark plug. It represents the highest grade of craftsmanship and reliability that have made Yamaha a leader. Crankcase And Crankshaft CRANKCASE AND CRANKSHAFT CRANKCASE AND CRANKSHAFT 1 Crankcase separation 2 Crankshaft removal Extent of removal: Before starting the engine, fill the fuel tank with the fuel.

Dado fusto dello sterzo: Steering bearing type Taper roller bearing Front suspension: VALVES AND VALVE SPRINGS VALVES AND VALVE SPRINGS 1 Valve removal Extent of removal: Special Tools SPECIAL TOOLS SPECIAL TOOLS The proper special tools are necessary for complete and accurate tune-up and assembly.

Page CYLINDER HEAD INSPECTION Cylinder head 1. Valve clearance cold 0. KICK SHAFT AND SHIFT SHAFT 3.

• REMOVING THE REAR WHEEL 1. Page KICK SHAFT AND SHIFT SHAFT 3.
• Page SPEC ALLGEMEINE TECHNISCHE DATEN Getriebeabstufung:
• CABLE ROUTING DIAGRAM Throttle cable Pass the clutch cable and hot Clamp starter cable through the cable Hot starter cable guide. SYSTEME DU CAPTEUR DE POSITION DE PAPILLON DES GAZ DROSSELKLAPPENSENSOR — ELEC SISTEMA SENSORE POSIZIONE FARFALLA
• Drain the fuel tank, fuel lines, and the car- buretor float bowl. Place an aluminum plate a between the teeth of the balancer shaft drive gear 3 and driven gear 4.
• SOUPAPES ET RESSORTS DE SOUPAPES VENTILE UND VENTILFEDERN VALVOLE E MOLLE VALVOLE Mesurer:
• CONTROLE ET REGLAGE DE LA TETE DE FOURCHE INSP LENKKOPFLAGER KONTROLLIEREN UND EINSTELLEN CONTROLLO E REGOLAZIONE TESTA DELLO STERZO Ecrou de direction: CARBURETOR CARBURETOR REMOVING THE CARBURETOR 4 Nm 0.

Timing chain tensioner Refer to removal section. Unlike OEM factory manuals, which are designed for the professional motorbike mechanic, Clymer shop manuals are designed specifically for the first time user.

Do not use a hammer to drive out the crankshaft.

YAMAHA YZF OWNER'S SERVICE MANUAL Pdf Download.

INSP FRONT BRAKE ADJUSTMENT NOTE: Refer to "EXHAUST PIPE AND SILENCER" Dates of Publications Vary By Manual. Maintenance Specifications MAINTENANCE SPECIFICATIONS Rear wheel travel mm Page CYLINDER HEAD ASSEMBLY AND INSTALLATION Cylinder head 1. Install the new pads "3" and the valve lifters "4".

Like my articles and How-To videos? INSP ENGINE OIL REPLACEMENT 7.

Yamaha YZ250F 2008 Owner's Service Manual

Valve lifter Use special tool. SPEC SPECIFICHE DI MANUTENZIONE SPECIFICHE DI MANUTENZIONE MOTORE Elemento Standard Limite Testata: Page INSP CLUTCH ADJUSTMENT NOTE: CAMSHAFTS Decompression system 1. CHAS FRONT WHEEL AND REAR WHEEL EC REMOVAL POINTS EC Rear wheel 1. Torque-check Points STARTING AND BREAK-IN INFO BREAK-IN PROCEDURES 1.

Tech Tip: Changing Oil On A Yamaha YZ250F - MotoUSA

Page CAMSHAFTS REMOVAL POINTS Camshaft 1. CHAS FRONT FORK Adjuster 1. ENGINE Use the new pad number only as a guide when verifying the valve clear- ance adjustment. The shape and part number used for the special tool differ by country, so two types are provided.

Page SEAT, FUEL TANK AND SIDE COVERS EC ENGINE SEAT, FUEL TANK AND SIDE COVERS 1 Seat removal 2 Fuel tank removal Extent of removal: Page OIL FILTER ELEMENT, WATER PUMP AND RIGHT CRANKCASE COVER REMOVAL POINTS Impeller shaft 1. Remove all dirt, mud, dust, and foreign material before removal and disassembly. Refer to "CRANKCASE AND CRANK- Separate the crankcase.

Page HANDLEBAR 5. Handling notes of coolant: NETTOYAGE DU FILTRE A AIR INSP LUFTFILTER REINIGEN PULIZIA DEL FILTRO ARIA Nettoyer: Shop by category Shop by category. CHAS REAR SHOCK ABSORBER EC REMOVAL POINTS EC Bearing 1.

If you have any questions regarding the operation or maintenance of your machine, please consult your Yamaha dealer. Page CLUTCH 7. Using the correct special tool will help prevent damage caused by the use of improper tools or improvised techniques.

Metodo di trasmissione Comando a catena lato sinistro Maintenance Specifications, Engine SPEC MAINTENANCE SPECIFICATIONS MAINTENANCE SPECIFICATIONS ENGINE Item Standard Limit Cylinder head: